Tool
Wet Felting Shrinkage Calculator: Size Your Layout or Resist
Enter the size you want to end up with and a shrinkage rate, or measure a test sample and let the calculator work out the rate for you.
Short answer
Wet felt usually shrinks 20 to 50 percent per side, and makers most often work with 30 to 45 percent. Layout size = finished size divided by (1 minus shrinkage). At 30 percent, a 12 inch piece needs a layout of about 17 inches (12 / 0.70). The only reliable rate is your own: lay out a 10 by 10 inch sample in the same wool and thickness, felt it fully and measure it.
How much does wet felting shrink?
Wet felt usually shrinks 20 to 50 percent per side. Makers most often work with 30 to 45 percent.
| Shrinkage | Multiply finished size by | Layout for 10 in finished | Layout for 30 cm finished | A 10 in sample ends at |
|---|---|---|---|---|
| 20% | 1.25 | 12.5 in | 37.5 cm | 8.0 in |
| 25% | 1.33 | 13.3 in | 40.0 cm | 7.5 in |
| 30% | 1.43 | 14.3 in | 42.9 cm | 7.0 in |
| 35% | 1.54 | 15.4 in | 46.2 cm | 6.5 in |
| 40% | 1.67 | 16.7 in | 50.0 cm | 6.0 in |
| 45% | 1.82 | 18.2 in | 54.5 cm | 5.5 in |
| 50% | 2.00 | 20.0 in | 60.0 cm | 5.0 in |
Published figures behind the range: AB Crafty gives 20 to 50 percent and uses 30 percent as its default, Sally Ridgway Designs 30 to 40 percent for scarves, Spirited Hands Studio about 45 percent for one maker, and a sample by Vanda F. Sousa went from 30 cm to 16.5 cm, which is 45 percent.
Shrinkage calculator
Enter the finished size and a shrinkage rate, or switch to the sample method and enter what your test square measured before and after felting.
Layout or resist size
Lay out 17.25 x 11.5 in
For a finished piece of 12 x 8 in at 30% shrinkage. Sizes are rounded up to the next 0.25 in, so the piece does not come out small.
- Multiplier
- Multiply finished sizes by 1.43
- Area
- The layout covers about 2.0 times the finished area
If your felt shrinks 25 to 35 percent, the layout length is 16 to 18.5 in.
Layout = finished size / (1 - shrinkage). The rates are published figures from feltmakers, not our own tests. Your own sample, and the pattern's or maker's instructions where they give a rate, win where they differ.
- The only reliable rate is your own sample: same wool, same number of layers, same method, measured when it is fully felted and dry.
- For a resist, scale each flat dimension of the template by the same multiplier.
- A common slip is adding the percentage to the finished size. 12 in plus 30 percent is 15.6 in, and a 15.6 in layout that shrinks 30 percent ends at 10.9 in, not 12. Divide by (1 - shrinkage) instead. If a pattern gives a shrink rate, check whether it means percent lost from the layout or a multiplier.
- A piece that comes out large can usually be fulled further. One that comes out small cannot be made bigger. When unsure, round up.
How to make and measure a sample
- 1
Lay out a square of 10 x 10 in (AB Crafty) or 30 x 30 cm, or 12 x 12 in (Vanda F. Sousa), with the same wool and the same number of layers as the project.
- 2
Felt and full it completely, the way the project will be worked.
- 3
Rinse it, let it dry and measure both directions.
- 4
Enter the numbers in the calculator under Work it out from a sample.
Shrinkage percent or multiplier: two ways to say the same thing
A shrinkage of 35 percent is the same as a multiplier of 1.54. The table at the top of the page converts between the two. Feltmakers also call the multiplier the coefficient of increase or the shrinkage rate, which is why a pattern's number has to be read with care.
- Shrinkage = (layout size - finished size) / layout size. Example from Lena Archbold: a scarf laid out at 200 cm that ends at 130 cm has shrunk 35 percent.
- Layout size = finished size / (1 - shrinkage). At 30 percent, 12 in needs 12 / 0.70 = 17.14 in, which the calculator rounds up to 17.25 in.
- Multiplier = layout size / finished size = 1 / (1 - shrinkage).
- Area: layout area / finished area = 1 / ((1 - shrinkage in length) x (1 - shrinkage in width)).
The calculator rounds layout sizes up to the next 0.25 in or 0.5 cm, shows the multiplier to two decimals and uses the unrounded rate of a sample in the arithmetic.
Why shrinkage rates differ
Vanda F. Sousa lists what moves the rate:
- The wool: breed, micron and fiber length. Fine wool shrinks more than coarse.
- The number of layers and their thickness. Thin layouts shrink more than thick ones.
- The layout method.
- Added decorations.
- How the piece is fulled, and the water temperature.
This page gives no shrinkage figure per wool type or per layer count: we could not verify a source with such figures, so only the direction of each effect is stated. For the wool itself, see wool for wet felting.
How many layers, and how much wool
Two to four thin layers at right angles is common. Felting and Fiber Studio describes 3 or 4 layers of wool top and notes that a batt equals about 3 to 4 layers. For hollow pieces the same multiplier sizes the template: resist materials compares what to cut it from.
| Project | Wool |
|---|---|
| Nuno scarf | 75 to 100 g of wool top |
| Hat | about 100 g |
| Pair of slippers | 200 g |
Note.Shrinkage is not a property of the wool alone. Two people felting the same wool get different rates. Treat every figure here as a starting point and trust your own sample.
We have not tested these rates. The range comes from the published figures of the feltmakers listed below. Where a pattern or a wool supplier gives its own rate, that figure wins for that project.
Sources
- AB Crafty: Wet Felting Wool Shrinkage Calculator
- Lena Archbold: Coefficient of Increase and a Percentage of Shrinkage
- Vanda F. Sousa: How much bigger should you make a resist
- Sally Ridgway Designs: Wool and fibre estimates for wet and nuno felting
- Spirited Hands Studio: article on shrink rate for wet felt makers
- Felting and Fiber Studio: Wet Felting